SMO1205A AGC Optical Receiver Module

SMO1025.PDF FEATURES ● Excellent Linearity ● High Optical Input Power Range ● Excellent Flatness ● Optimal Reliability ● Low Noise ● Outline Standarding ● GaAs MMIC ● High reliability ● FC/APC SC/APC   DESCRIPTION The SMO1025 has an FC/APC or SC/APC connector. Pin Description The amplifier supply voltage pin is connected to 24V(DC) . The CATV GaAs Optical Receivers have a mono mode optical input suitable for 1290 to 1600nm wavelengths a terminal to monitor the photo diode current and an electrical output having a characteristic impedance of 75Ω. CHARACTERISTICS (Bandwidth 40 to 1005MHZ; Tmb＝25℃, VB＝24V, ZS＝ZL＝75Ω) SYMBOL PARAMETER UNIT MIN. TYP. MAX. CONDITIONS Responsivity V/W 850 - - λ=1300nm Flatness straight line dB - - ±0.75 f=40 to 1005 MHZ Output voltage dBμV - 88 - 110 channels flat; Popt= - 1dBm; CTB measured at 745.25 MHz; CSO measured at 746.5 MHz; Composite triple beat dB - -65 - Composite second order distortion dB - -63 - Carrier to noise ratio dB - -51 - Output return loss dB - -11 - f=40 to 1005 MHZ Total current consumption mA 240 - 290 VB=24V The module normally operates at VB=24 V(±0.5)

Mini V-ONU F01.pdf 1. SCOPE This document describes basic electrical characteristics and mechanical characteristics of optical receiver FTTH-F01, which is produced in Shenzhen, PRC.  2. ELECTRICAL SEPCIFICATION 2.1 INPUTRANGE 2.1.1 OPTICAL INPUTRANGE Optical receiver FTTH-F01 should operate within specification of optical input range from -15dBm to -5dBm. 2.1.2 DC INPUTRANGE Optical receiver FTTH-F01 should operate within specification of DC input range from 4.8V to 5.2V.  2.2 OUTPUT LEVEL The optical receiver should operate within specification of output level from 70dBµV to 73dBµV with optical input range is from -15dBm to -5dBm.  2.3 ESD SENSITIVITY The optical receiver should operate within specification of ESD sensitivity according to the table below: ESD ESD sensitivity Human body model; R=1.5KΩ;C=100pF MAX=500 1 V 2.4 RF PERFORMANCE REQUIRMENT 2.4.1 BANDWIDTH The optical receiver should operate within specification of band width from 47MHz to 1000MHz 2.4.2 OUTPUT RETURNLOSS The exact output return loss should apply the specification that S22 ≦-14dB 2.4.3 DISTORTION REQUIREMENT The optical receiver should operate within specification of distortion requirement according to the table below: Composite Triple Beat dB - - -58 60 channels; Measured at 543.25MHz Optical power@- 10dBm Composite Second Order distortion dB - - -58 Noise carrier rating dB 43 - - 2.5 OPTICAL PERFORMANCE SPECIFICATION See the table below: Parameter λ1 1530 1550 1570 nm Optical Wavelength Range R 0.90 0.95 - A/W Op=0dBm ， λ=1550nm Responsivity Id - 0.3 0.5 nA Dark Current IL - - 0.7 dB Insert Loss ORL - - - dB Return loss - 45 - λ=1550nm λ=1550nm Optical Connector - SC - Green Green 3. ENVIRONMENTAL SPECIFICATION 3.1 TEMPERATURE The temperature include storage temperature and operating temperature, and the optical receiver should apply to the temperature specification as the table below 3.1.1 ABSOLUTE MAXIMUM RATINGS Parameter Symbol Unit Min Typ Max Note Optical Input Power Pin dBm - - +2.0 Levels above max range may result in (latent) damages to the machine Storage Temperature T-storage ºC -40 - +85 10 ... 95 % relative humidity; non-condensing 3.1.2 OPERATING ENVIRONMENTAL LIMITS Parameter Symbol Unit Min Typ Max Note Case Temperature T-case ºC 0 - +80 10 ... 80 % relative humidity; non-condensing Power Supply Voltage VPSU V 4.8 5.0 5.2 Power Consumption PPSU W - 0.6 1 VB=5V FTTH-F01 RF SPECIFICATIONS: Parameter Symbol Unit Min Typ Max Note RF passband FPB MHz - 75 - Minimum BW; RF output impedance Rimp_out Ω - - - AGC working range for optical input power Rimp_out dBm -15 - -5 Optical AGC will be implemented,the average optical input power controls the gain. RF output level RFout dBµV 70 72 73 Optical power input range in --5dBm~-15dBm Flatness Flatness dB - ±1 47~1000MHz Output Return Loss ORL dB - - -14 Modulation Error Ratio MER dB 33 - -  - Total 96channels input ,OMI=3.5%,Optical power@-15dBm Bit Error Ratio BER dB 1e-8 CNR CNR dB 43 60 channels; Measured at 543.25MHz Optical power@-10dBm CSO CSO dBc - - -58 CTB CTB dBc - - -58 Total current consumption(DC) Itot mA 130 - 170 VB=5V If you want to know more our product details,Please reply to get E-Catelog and FOC samples,Thank you.

AVG1009.PDF Specification: Brande:OEI Part Number:MMIC-AVG1009 Product Origin:China Lead Time:According to Order Quanlity MOQ:>=1000 Free samples:Support Payment:TT/LC   Product Features ● -15dBm to -5dBm Optical Input Range. ● Single +5V Suppl ● 29dB Gain at 55MHz；34dB Gain at 1 ● 22dB Gain Control Ran ● +24dBmV/ch Output at 550 ● Lead-free/RoHS compliant QFN4X4－24L package Product Performance (Ta=25℃) Symbol Parameter1 Units Frequency Min. Typ. Max. G Trans-Impedance (Max. Gain State) dB 0.05 GHz 0.87 GHz 1GHz 26.5 31.0 31.5 29.0 33.0 34.0 30.5 35.0 35.5 GT Gain Tilt dB 7 G Range Gain Control Range dB 0.05 GHz 0.87 GHz 1GHz 25.5 23.0 24.0 29.0 26.0 27.0 32.0 29.0 30.0 VAGC AGC Control Voltage Range V +3 - 0 RL Output Return Loss dB 0.05-1 GHz -18 EIN2 Equivalent Input Noise pA/rtHz 0.05-1 GHz 3.2 IDD Attenuator Current mA VDD=+5V 160 170 180 1. All measurements in a 75 Ohm system, unless otherwise specified. 2. Specified at maximum gain(VAGC=+3V).  

SDU RFOG D01.PDF Product Description： The RFoG Mini Node is a small home optical node specially developed for cable TV operators using the DOCSIS protocol standard, to provide users with two-way,interactive TV and network services. Compared with other two-way optical nodes, this series of products has the characteristics of small size, flexible networking and high cost performance.   FEATURES ： 1) Designed for DOCSIS network 2) Forward 1550nm input power: -9~+3dBm, forward AGC Range: -6~+2dBm 3) Forward frequency: 54~1200MHz, EQ 3±1.5dB, RF output level: 73dBuV 4) Reverse 1610nm output Power: 2mW. 5) Reverse frequency: 5~42MHz, RF input level: 75~112dBuV 6) LED on the housing for forward optical power, reverse optical power and 1V/ mW forward optical power. 7) With -20dB RF output test port. 8) Power consumption ＜3W. 9) Compact Aluminium cast housing, perfect heat dissipation 10) Fully Compatible with SCTE Standards.

SMG1227.PDF FEATURES ● GaAs active devices ● Power gain @27dB ● Low distortion ● Excellent linear gain ● Low noise figure ● High reliability ● Low cost   DESCRIPTION The SMG1227 is a GaAs hybrid push-pull amplifier module. The part employs GaAs dies and is operated from 50 MHz to 1218MHz with supply voltage +24V(DC).  CHARACTERISTICS (Bandwidth 50 to 1218MHZ; Tmb＝25℃, VB＝24V, ZS＝ZL＝75Ω) SYMBOL PARAMETER UNIT MIN. TYP. MAX. CONDITIONS Gp Power Gain dB 26 27 27.5 f=50MHZ Gp Power Gain dB - 28 - f=870MHZ Gp Power Gain dB 27.5 28.0 29.0 f=1218MHZ SL Slope cable equivalent dB 1.0 2.0 3.0 f=50 to 1218 MHZ SL Flatness of frequency response dB - - ±1.0 f=50 to 1218 MHZ S11＆S22 Input ＆Output Return Loss dB - - -20 f=50 to 320 MHZ S11＆S22 Input ＆Output Return Loss dB - - -19 f=321 to 640 MHZ S11＆S22 Input ＆Output Return Loss dB - - -17 f=641 to 1000 MHZ S11＆S22 Input ＆Output Return Loss dB - - -16 f=1000 to 1218 MHZ CTB Composite Triple Beat dB - -68 -63 PAL99 channelsflat; Vo=43dBmV; CTB measured at 543.25 MHz; CSO measured at 544.5 MHz; CSO Composite Second Order distortion dB - -66 -61 Xmod Cross Modulation dB - -67 - Vo Output Voltage dBmV 60 - - dim=-60dB F Noise Figure dB - 4.5 5.0 f=50 to 1218 MHZ Itot Total Current Consumption mA 260 270 290 VB=+24V The module normally operates at VB=24 V(±0.5) If you want to know more our product details,Please reply to get E-Catelog and FOC samples,Thank you.

Download product specification：SMO2700.PDF FEATURES ● Excellent Linearity ● Extremely low noise ● Excellent flatness ● Rugged construction ● FC/APC ● AG   DESCRIPTION SMO2700 CATV AGC Optical Receiver Module is a low power, but good performance optical receiver. Output level is 70dBuV @-5dBm. Small size with FC/APC connector which can be assembled in a small case. CHARACTERISTICS (Bandwidth 45 to 1000MHZ; Tmb＝25℃, VB＝5V, ZS＝ZL＝75Ω) SYMBOL PARAMETER UNIT MIN. TYP MAX. CONDITIONS S responsively V/W 850 - - λ=1300nm-1600nm FL1 Flatness of frequency response dB - ±1.0 ±1.5 f=45 to 1000 MHZ, wide band flatness FL2 Flatness of frequency response dB - - ±0.4 Narrow bandwidth per 7MHz SL Slope dB - 2 3 From 45~900MHz S22 Output Return Loss dB - - - f=45 to 900 MHZ S22 Output Return Loss dB - - - f=1000 to 2700 MHZ Itot Total Current Consumption mA - - 220 VB=5V Automatic Gain Control Receiving Power: -10~0dBm (According to customer requirements) Vo1 Output Voltage dBuV 70 - - - - Popt= -5dBm BW=45~900MHz 42 channels T=25℃ OMI=4% per channel - - - - - - Vo1 Output Voltage dBuV 68 - - - - Popt= -5dBm BW=45~900MHz 42 channels T=0~40℃ OMI=4% per channel - 80.5 - - - SYMBOL PARAMETER UNIT MIN. TYP. MAX. CONDITIONS CTB Composite Triple Beat dB - - -60 Optical power -3dBm 42 channels PAL-D .175.25MHz OMI=4% per channel CSO Composite Second Order distortion dB - - -60 C-spurious Carrier to spurious dB - - -57 CTB Composite Triple Beat dB - - -57 Optical power +1dBm 42 channels PAL-D .175.25MHz OMI=4% per channel  CSO Composite Second Order distortion dB - - -56 C- spurious Carrier to spurious dB - - -56 CNR Noise carrier rating dB 45 - - Optical power -7dBm 42 channels PAL-D .175.25MHz OMI=4% per channel - - - - Please note:  Vo1 are according to the optical change from -10dBm ~0dBm. For example, In -10dBm the output level is 80dBuV, but in the 0dBm maybe output level is 82dBuV.  Vo2 are according to the temperature change .for example: when the temperature stay 40℃,the output level will lower 0.5dB than 25℃. When the temperature stay 0℃,the output level will higher 0.5dB than 25℃. If you want to know more about our product details,Please reply to get E-Catelog and FOC samples,Thank you.

SMG2342R.PDF FEATURES ● Si active devices ● Power gain @35dB ● Low distortion ● Excellent linear gain ● Low noise figure ● High reliability ● Low cost   DESCRIPTION The SMG2342R is a hybrid push-pull amplifier module. The part employs GaAs dies and is operated from 5 MHz to 200MHz with supply voltage +24V(DC).  CHARACTERISTICS (Bandwidth 5 to 200MHZ; Tmb＝25℃, VB＝24V, ZS＝ZL＝75Ω) SYMBOL PARAMETER UNIT MIN. TYP. MAX. CONDITIONS Gp Power Gain dB 34.5 - 35.5 f=10MHZ Gp Power Gain dB - 35 - f=200MHZ SL Slope cable equivalent dB -0.5 - +0.5 f=5 to 200MHZ FL Flatness of frequency response dB - - ±0.5 f=5to 200MHZ S11 Input Return Loss dB - - -18 f=5 to 200MHZ S22 Output Return Loss dB - - -18 f=5 to 200MHZ CTB Composite Triple Beat dB - - -66 17channels flat; Vo=50dBmV; CSO Composite Second Order distortion dB - - -65 Xmod Cross Modulation dB - - -60 F Noise Figure dB - 4.3 - f=200 MHZ Itot Total Current Consumption mA 130 160 - VB=+24V If you want to know more our product detais,Please reply to get E-Catelog and FOC samples,Thank you.

Applications: ● CATV optical receiver ● CATV Amplifier ● FTTH Network